Thermo Scientific 3110 CO2 Water Jacketed Incubator w/ Copper Interior

The Thermo Scientific 3110 CO2 Water Jacketed Incubator w/ Copper Interior combines precise CO2 control with temperature control and is the most popular incubator on the market. The Forma Series II Water Jacketed CO2 Incubator, with its precise CO2 control, elevated RH, and a thermal conductivity sensor, is the first choice for many researchers. These incubators feature unsurpassed temperature stability and superior parameter recovery characteristics, with innovative continuous contamination control technology. The 3110's 100% HEPA filtration quickly achieves Class 100 air quality. The HEPA filter entraps particulate air contaminants and prevents their escape, and filter efficiency increases as particulates and micro-organisms are entrapped. Temperature retention and quick recovery are especially important for researchers working with critical cell cultures. The Thermo Scientific 3110 CO2 Water Jacketed Incubator w/ Copper Interior provides maximum thermal protection and quick recovery from swings in ambient temperature and power variations.

All of our equipment is fully tested to perform at factory specifications before being shipped.

Thermo Scientific 3110 CO2 Water Jacketed Incubator w/ Copper Interior Specifications

Incubator Inspection and Recertification Checklist

• Inspect the display for any dim, flickering, or dead pixels, replacing any affected areas to maintain full readability and operational clarity
• Thoroughly examine external regulators for any signs of damage, wear, or malfunction (if applicable), replacing any compromised parts
• Inspect temperature, COâ‚‚, and Hâ‚‚O sensors (if applicable), ensuring each sensor is functioning correctly and accurately reporting conditions
• Conduct a detailed inspection of all internal wiring for frays, tears, or breakages; replace any compromised wires to ensure safe and reliable connections
• Verify that software settings align with the internal components and calibration specifications, adjusting configurations as needed for accurate operation
• Inspect and clean the fan, ensuring it is free from dust or obstructions; replace if performance is below required standards
• Examine wheels and leveling mounts for structural integrity, ensuring proper balance and stability for safe operation
• Inspect door gaskets and latches for any signs of wear or damage, replacing if necessary to maintain a secure seal and optimal environmental control
• Calibrate temperature accuracy at 37°C using a NIST-traceable probe, confirming it meets required tolerances
• Calibrate COâ‚‚ level to 5% using a Fyrite combustion test kit (if applicable), ensuring precise atmospheric conditions
• Monitor temperature and COâ‚‚ stability over a 24-hour period, verifying consistent operation within specified ranges
• Conduct a thorough cosmetic inspection to confirm all external surfaces and components meet quality standards, free from visible damage or wear

Technician Inspection and Recertification Checklist: Incubator

The Following Checklist Is to Be Performed on All Incoming and Outgoing Pieces of Equipment

Task	Completed?	Remarks?
Inspect display for dim, flickering, or dead pixels; replace for readability	Completed
Examine external regulators for damage or malfunction; replace compromised parts	Completed
Inspect temperature, COâ‚‚, and Hâ‚‚O sensors for correct function and accuracy	Completed
Inspect internal wiring for frays, tears, or breakages; replace compromised wires	Completed
Verify software settings align with components and calibration specs; adjust if needed	Completed
Clean fan and remove dust/obstructions; replace if performance is substandard	Completed
Examine wheels and leveling mounts for structural integrity and balance	Completed
Inspect door gaskets and latches for wear or damage; replace to maintain seal	Completed
Calibrate temperature at 37°C with NIST-traceable probe to confirm accuracy	Completed
Calibrate COâ‚‚ level to 5% with Fyrite test kit for atmospheric precision	Completed
Monitor temperature and COâ‚‚ stability over 24-hour period to verify consistency	Completed
Conduct cosmetic inspection to confirm quality of external surfaces and components	Completed

102 Tide Mill Road, Hampton NH 03842
customerservice@marshallscientific.com | (603) 601-8511 |
www.marshallscientific.com
Copyright © 2024 by Marshall Scientific LLC. All rights reserved.

To View More of Our Recertification Protocol Click Here