VWR 1535 Digital Incubator
Temperature Range
Ambient +5°C to 70°C
Temperature Uniformity
± 0.25°C at 37°C
Capacity
6.7 cu. ft.
Features
- Quick temperature recovery ensures efficient operation
- Full-length inner glass door allows specimen viewing without atmospheric disturbance
- Microprocessor control for easy parameter setting and calibration
- Temperature display can be calibrated to match a secondary thermometer
- Provides temperature stability of ± 0.1°C
- Includes over-temperature protection with a secondary independent safety controller
- Visual alarm activates when safety limits are exceeded
- Through-wall access port accommodates a chart recorder
The VWR 1535 Digital warm air incubator provides quick temperature recovery and has a full-length inner glass door for viewing specimens without disturbing the chamber atmosphere. Microprocessor control allows easy keypad parameter setting and calibration. The temperature display may also be calibrated to match a secondary thermometer. For over-temperature protection, a second, independent safety controller can be preset and has visual alarm when activated. Features through-wall access port for chart recorder. The VWR 1535 is a 6.7 cubic foot unit that offers temperatures from 5°C above ambient to 70°C with a uniformity of ± 0.25°C and stability of ± 0.1°C.
All of our equipment is fully tested to perform at factory specifications before being shipped.
INCLUDED:
The VWR 1535 Digital Incubator includes:
The VWR 1535 Digital Incubator includes:
- > Calibration
- > 2 Shelves
- > Power Cord
- > Operator's Manual
- > Full 180 Day Parts and Labor Warranty
VWR 1535 Digital Incubator Specifications
|
Temperature Range |
Ambient +5°C to 70°C |
|
Temperature Uniformity |
± 0.25°C @ 37°C |
|
Temperature Stability |
± 0.1C |
|
Capacity |
6.7 cu ft |
|
Interior Dimensions (W x D x H) |
24 x 24 x20 in |
|
Exterior Dimensions (W x D x H) |
30 x 30 x32 in |
|
Electrical Requirements |
115V, 50/60Hz, 5A |
Incubator Inspection and Recertification Checklist
- Inspect the display for any dim, flickering, or dead pixels, replacing any affected areas to maintain full readability and operational clarity
- Thoroughly examine external regulators for any signs of damage, wear, or malfunction (if applicable), replacing any compromised parts
- Inspect temperature, COâ‚‚, and Hâ‚‚O sensors (if applicable), ensuring each sensor is functioning correctly and accurately reporting conditions
- Conduct a detailed inspection of all internal wiring for frays, tears, or breakages; replace any compromised wires to ensure safe and reliable connections
- Verify that software settings align with the internal components and calibration specifications, adjusting configurations as needed for accurate operation
- Inspect and clean the fan, ensuring it is free from dust or obstructions; replace if performance is below required standards
- Examine wheels and leveling mounts for structural integrity, ensuring proper balance and stability for safe operation
- Inspect door gaskets and latches for any signs of wear or damage, replacing if necessary to maintain a secure seal and optimal environmental control
- Calibrate temperature accuracy at 37°C using a NIST-traceable probe, confirming it meets required tolerances
- Calibrate COâ‚‚ level to 5% using a Fyrite combustion test kit (if applicable), ensuring precise atmospheric conditions
- Monitor temperature and COâ‚‚ stability over a 24-hour period, verifying consistent operation within specified ranges
- Conduct a thorough cosmetic inspection to confirm all external surfaces and components meet quality standards, free from visible damage or wear
Technician Inspection and Recertification Checklist: Incubator
The Following Checklist Is to Be Performed on All Incoming and Outgoing Pieces of Equipment| Task | Completed? | Remarks? |
| Inspect display for dim, flickering, or dead pixels; replace for readability | Completed | |
| Examine external regulators for damage or malfunction; replace compromised parts | Completed | |
| Inspect temperature, COâ‚‚, and Hâ‚‚O sensors for correct function and accuracy | Completed | |
| Inspect internal wiring for frays, tears, or breakages; replace compromised wires | Completed | |
| Verify software settings align with components and calibration specs; adjust if needed | Completed | |
| Clean fan and remove dust/obstructions; replace if performance is substandard | Completed | |
| Examine wheels and leveling mounts for structural integrity and balance | Completed | |
| Inspect door gaskets and latches for wear or damage; replace to maintain seal | Completed | |
| Calibrate temperature at 37°C with NIST-traceable probe to confirm accuracy | Completed | |
| Calibrate COâ‚‚ level to 5% with Fyrite test kit for atmospheric precision | Completed | |
| Monitor temperature and COâ‚‚ stability over 24-hour period to verify consistency | Completed | |
| Conduct cosmetic inspection to confirm quality of external surfaces and components | Completed |
102 Tide Mill Road, Hampton NH 03842
customerservice@marshallscientific.com | (603) 601-8511 |
www.marshallscientific.com
Copyright © 2024 by Marshall Scientific LLC. All rights reserved.
VWR 1535 Digital Incubator Manual
Click Here to View all the Technical Specs for the VWR 1535
Click Here to View the Technical Specs for the VWR 1535
